#Gnuradio morse decoder mod#
#Gnuradio morse decoder update#
#Gnuradio morse decoder driver#
#Gnuradio morse decoder software#
#Gnuradio morse decoder code#

wav file without any GUIs running still gives the same error. Looking online, this seems to be a sound issue.

#Gnuradio morse decoder code#

If I increase my base sampling rate from 96kHz to 256 kHz, I just get a constant pitch and the code fails but I get “OaOaOaOaOa” like GNURadio is chanting for me.

#Gnuradio morse decoder update#

Every GUI takes forever to update (around 0.2ms no matter the refresh rate), so I think I am not processing the audio fast enough.

#Gnuradio morse decoder software#

I chose 10 kHz as the tone frequency which fits nicely in all my Nyquist theorems (overall sampling rate is 96kHz, audio sampling rate is 24 KHz), but the software seems to just be running too slow. I can’t actually get an audible signal out of this. Iteration 1: DiPole>RG1746ft>TV amplifier>RG620ft>RTLSDRV3>Rpi on a deck on a 5ft tripod. Simple enough right? Here’s where things get tricky. Hi, I built a QFH antenna last week and below is my progress so far. My resulting time-domain wave looks like this with the binary bits (On/Off) overlayed to a sine wave (red It’s the same way it’s generated! My flowgraph looks like this: Audio ReceptionĮssentially to actually hear the morse code, I keyed a sine wave on and off. I was about to use MATLAB and fill matricies for 10e5 bits. I even had a frequency comparator and found the frequency for the dits to be about 3600 Hz: My flowgraph now looked like this:įrom this point, I was dead-set on decoding using bit containers and fancy logic statements. So all I needed to do from this point was threshold at this amplitude change to find my 1s and 0s.

Looking at the time domain, I saw several spikes in amplitude at the presence of a CW tone: So now you have a basic filtered USB signal. The basic flowgraph for USB looks like this: Remember to save your project as something different, since you may need to start back at square one (as I have done several times). Using the custom flowgraph as mentioned earlier, you already get a headstart with receiving.

Below is the raw spectrum for my signal:Īnd each transmission starts with this cool design in the waterfall: The WiFi and World Wide Wardrive also seem promising. I tried the morse challenge first since it seemed the most straightforward. You poke around on the ports for the correct signal, and get decoding. grc found here.Įssentially for each stage of the SDR ctf you are given a ZMQ port to listen on in gnuradio via these blocks. Continue reading for my nearly complete solution to one of the tests with my. The Radio Frequency Hacker Sanctuary launched a virtual capture-the-flag event involving digital signal processing, quick thinking, and gnuradio. However, a lot of the fun happened virtually. In contrast, the Planar Disk is almost free and it performs quite well in an indoor setting.I recently had the awesome opportunity to attend DEFCON29 in person. Just because an antenna 'is sold' does not mean its good or even marginal. Please verify your dongle is working with a good antenna before complaining that you cannot receive something. Here is a great, broadband Planar Disk Antenna that outperforms most commercial antennas of similar size for under $65-75 and can be built in a half hour or less by beginners with less than $10 in parts. See our wiki with tutorials and other resources including a Quick Start page to verify your dongle works.

#Gnuradio morse decoder driver#

The rtl-sdr project page Source of the rtl-sdr driver software and hub for its continued development. Resources - Please read this first - before posting! Max sample rate: 3.2 MS/s (2.6 MS/s in practice).Frequency range : 24 - >1760 MHz (100 KHz - 24 MHz in direct sampling mode).Typical specs (some depend on specific tuner):

All rtl-sdr compatible devices employ the RTL2832U as an ADC and USB controller, but different RF tuners may be used. 'rtl-sdr' is a generic term for cheap USB digital TV (DVB-T) receivers that use the Realtek RTL2832U chipset, which can function as general purpose software defined radios (receive only). Morse Code Translator is a translator that lets anyone translate text to Morse code and decode Morse code to text easily. While originally dedicated just to the rtl-sdr project, relevant legal content related to general SDR, RF and similar projects is also welcomed.įeel free to ask questions but please check the wiki first. Use self / text posts for your immediate inquiries and general posts.Ī subreddit for the low-cost, DIY software defined radio (SDR) community.

#Gnuradio morse decoder mod#

Link / Image posts are now sent to the Mod Queue before appearing.